March 24, 2023
In early March, we shipped a series of testing equipment for electric vehicle supply equipment. Let me give you a brief introduction:
1. EVSE Testing Equipment Connector Plug Cable Strain Relief Test
This mechanical strength inpact test equipment complied to IEC 61851-1 2017 clause 12.11 standards.
Technical Parameter:
| Control and operation | PLC control, 7-inch color touch screen control, remote control remote control. |
| Drive mode | Motor + reducer mechanism |
| Pendulum impact | |
| Impact force | Standard 5J (10J, 20J, 50J optional) |
| Pendulum mass accuracy | ±1% |
| Equivalent mass of impact hammer | 1.7kg (5 kg, 5 kg, 10 kg are optional) |
| Impact hammer form | Spherical impact hammer |
| Pendulum striking point height adjustment range: | Customized according to the sample |
| Pedulum arm height adjustment range | 200-500mm |
| Specimen clamping adjustment range | Customized according to the sample |
| Impact point height adjustment | Electric adjustable |
| Number of impacts | 0-9999 times can be preset |
| Status indication | LED indicator |
| Pendulum height (energy) adjustment | Manual adjustment |
| Pendulum positioning | Electromagnet adsorption |
| Pendulum release | Wireless remote control or touch screen operation |
| Impact point height adjustment method | Wireless remote control or touch screen operation |
| Security | 360° all-round safety protection, automatic electric brake to prevent secondary impact |
| Vertical impact | |
| Impact force | Standard 5J (10J, 20J, 50J optional) |
| Installation method | The hammer head is adsorbed by electromagnet, and the conduit is screw-in type |
| Release method | Button control, electromagnet momentary release |
| Hammer release | Remote control |
| Height adjustment method | Remote control |
2. EVSE Testing Equipment Connector Plug Cable Strain Relief Test Equipment
This Connector Plug Cable Strain Relief Test Equipment complied to IEC 61851-1 2017 Electric vehicle conductive charging system - Part 1: General requirements clause 11.6, IEC 62196-1 Ed.4CDV 2020 clause 25.3 Figure 17 and table 11 and IEC60309-1: 2012 clause 23.3, etc.
Technical parameter:
| Operation Method | Button operation |
| Drive Mode | Motor and cylinder |
| Pull Force Weights |
40N*2, 50N*2, 60N*1, 110N*1,250N*1 Can achieve 160N, 200N, 240N, 250N,500N,600N pull force |
| Torque Weights |
6N*1, 7N*1, 12N*1, 15N*1, 23N*1, 110N*1 Can achieve 0.6N.m, 0.7N.m, 1.2N.m, 1.5N.m, 2.3N.m, 11N.m torque |
| Torque Arm | Ф200mm |
| Pull Frequency | 1 cycle/s |
| Pull Cycles | 1-999999 cycles, can be preset, default 100 cycles |
| Torque Applied Time | 0-99999.9S, can be preset, default 1 min |
| Fixture | One set of universal fixtures |
| Equipment Dimensions & Weight | L 1560mm*W 600mm*H 1530mm, approx. 220KG |
| Power Supply | Single phase AC220V±10%, 50/60Hz or AC110V, 60Hz |
3. EVSE Cord Cantilever Tensile And Rocking Life Tester
The EVSE cord cantilever tensile and rocking life test device is a non-standard customized equipment. At the same time, it can also be tested to find out which parts of the sample are more likely to be damaged and whether the electric vehicle supply equipment is safety. It is a necessary durability test equipment for laboratory research and development.
The customized fixture of the equipment meets the clamping requirements of samples of different sizes and shapes, and simulates the real operation as much as possible to make cantilever stretching movements. Since the cantilever stretching and rebounding action is completed by a similar weight load, the cantilever stretching part only needs to make a stretching action, and then cooperate with the load to recover the wire rope.
The swing life tooling part is mainly used for the life test of the sample swinging from side to side. The machine is controlled by PLC & Touch screen. You can input the swing angle, speed and number of tests on the touch screen by yourself, and press to start the test. When the set number of times is reached, it will automatically stop with an audible alarm signal. The whole machine is beautiful in appearance and easy to operate. The sample holder can be adjusted up and down, which can adapt to the testing needs of different samples.
Technical Parameter:
| Power supply | 220V/50hz |
| Test station | 2 stations: 1 station cantilever stretching, 1 station swing |
| Tooling information | The cable clamp can hold the charging gun cable with a diameter of 30~60mm |
| Swing angle | -90~+90 degrees |
| Swing speed | 1~20 times/min |
| Test times | 1~999999 times can be set |
| Control method | PLC & touch screen control |
| Drive mode | Servo motor + reducer |
| Stretching height stroke | 500~2000 (mm) |
| Stretching Speed | Speed 1.5m/s±50% adjustable (5-30 times/min adjustable) |
| Alarm method | Automatic alarm when the preset times are reached |
| Stretching uses a motor to drive a wire rope to stretch | |
| The height of the whole machine is about 2.5m, and it can adapt to samples below 2 meters in height. | |
-
28 Aug, 2024
-
27 Jul, 2024
-
28 Jun, 2024
-
30 May, 2024
-
28 Apr, 2024
-
9 Mar, 2024